FREE SHIPPING AVAILABLE ON ORDERS OVER £75.00*
PROXL PlastiGrip Adhesion Promoter Spray 500ml
An advanced adhesion promoter suitable for most types of plastic.
- Outstanding plastic adhesion promoter spray
- Can be overcoated with any topcoat
- Very fast drying
- Clear film
- Supplied with 2 nozzles
£12.08 exc VAT | £14.50 inc VAT
7 in stock (can be backordered)
Stay Social. Connect with us.
- Description
- Data Sheets
- Technical Information
- How To Apply
- Directions For Use
- Reviews (0)
- Trustpilot Reviews
Product Description
PROXL PlastiGrip Spray is an advanced plastic adhesion promoter, suitable for most types of plastic. It is a very fast drying coating that can be overcoated after just 30 minutes.
The coating creates a clear film on the surface that is suitable for any topcoat, such as PROXL PlastiColour for repairing bumpers and similar surfaces.
PlastiGrip can be applied to many different types of plastic, some of which would be difficult to paint otherwise. These include PP, PP/EPDM, ABS, SAN, PC, PA, PUR-RIM, R-TPU, PPO, PBT, PUR Flexible foam and UP-GF plastic.
Coverage: 3.8 – 5m²
Product Documents
Coverage: 3.8 – 5m²
Suitable Substrates (cleaned & abraded): PP, PP/EPDM, ABS, SAN, PC, PA, PUR-RIM, R-TPU, PPO, PBT, PUR Flexible foam and UP-GF plastic
Allow 10 minutes to flash off before overcoating.
Application Guide:
- Carry out test spray
- Areas to be sprayed must be free of grease, dust and dry
- For professional use only
- Wear an appropriate respirator
Application Process:
- Shake aerosol for at least two minutes, after agitator ball is free
- Apply in cross coats from distance of 250mm from object
- Allow 10mins for flash off before overcoating
- Apply 1 coat at 1-2μm
- After use, turn aerosol upside down and empty valve
Surface Preparation
Proper surface preparation is essential for the success of any protective coating system. Before you begin ensure the area is free from any dust, oil, grease, old coatings and surface contaminants.
The preparation of steelwork prior to painting generally falls into two main areas; that of degreasing and the removal of rust and scale.
All surfaces to be painted should be clean, dry and free from loose and flaking material, dust, grease and millscale, etc.
Prime bare surfaces with Palatine Anti-Corrosive Metal Primer or Palatine All Purpose Primer / Undercoat in accordance with our recommendations
For non-ferrous metals use Palatine Fast Dry etching primer.
Rub down previously gloss painted surfaces with fine waterproof abrasive paper and rinse thoroughly.
Mixing
Stir the paint with a drill stirrer or wooden baton at least 2” wide. Continue to stir during application.
Application
Best results are obtained in warm (minimum 10°C), dry conditions.
Mix thoroughly for approximately 2 minutes using a drill stirrer. A wooden batten at least 25mm wide is also ideal.
Apply an even coat using a brush, short to medium pile roller on smooth surfaces and a long pile roller on textured surfaces
For spray application by either airless or conventional spray a dilution ration of no more than 10% is recommended with Palatine White Spirit by volume applying thin coats allowing each one to dry before applying subsequent coats.
Once dried, a second coat can be applied at full strength. This will prolong the life and performance of the coating.
Thinning and Cleaning: Use Palatine White Spirit.
If using more than one batch of the same colour, intermix before use
Preceding Coat
Prime bare surfaces with Palatine Anti-Corrosive Metal Primer or Palatine All Purpose Primer / Undercoat in accordance with our recommendations
For non-ferrous metals use Palatine Mordant Solution.
Subsequent Coat
A second coat is recommended for maximum protection.
Be the first to review “PROXL PlastiGrip Adhesion Promoter Spray 500ml”
You may also like…
Car Spray Paint
£12.10 exc VAT | £14.52 inc VAT
Body Shop Primer
£15.68
Reviews
There are no reviews yet.