Survey Line Marking Spray Paint 750ml All Colours

FREE SHIPPING AVAILABLE ON ORDERS OVER £75.00*

Survey Line Marking Spray Paint 750ml

Survey Line Marking Spray Paints are used to create temporary lines for construction and safety purposes.

Can be applied to surfaces including bitumen, concrete, grass, soil, gravel, plants and timber
Touch dry in 25 minutes
Xylene free
Zero-Block™ (guaranteed not to clog)

£3.38

Stay Social. Connect with us.

Product Description

Survey Line Marking Spray Paints are used to create temporary lines on a range of ground surfaces. They are ideal for marking areas for construction and temporary hazards, with multiple colours available to mark out different areas. The survey paint markers can be applied to almost any type of surface, including concrete, bitumen, gravel, timber, soil, grass and plants.

The lines created with this survey paint start to disintegrate after 2 to 3 months (depending on UV exposure and surface), creating temporary markings for short term use. For creating permanent lines, please see the Acrylic Line Marker Spray 750ml.

Please note: The colours on the product listings are only given as a guide. This is due to the fact that every computer monitor has a different capability to display colours. In addition, everyone sees these colours differently.

Size: 750ml Aerosol
Colour: Yellow, Red, Blue, White, Green, Black and Orange
Colour lasting time: 2-3 months before it starts to disintegrate (can vary based on external factors such as UV exposure, surface material etc)
Propellant: LPG
Applications: indoors and outdoors
Drying (at 20°C, 50% relative air humidity):
Dust-dry: after approx. 15minutes
Dry to touch: after approx. 25 minutes Can be overworked: after approx. 24 hours
The drying time depends of temperature of surroundings, air humidity and thickness of the applied layer.
Recommended primer: not necessary
Emission rate: ≥96%
Layer thickness at 1.5 cross coats: about 130-150um
Processing temperature: from +5 – +40° C
One piece( 450g N.W.) can spray: approximately 100 meters
Storage stability: 24 months

Product Documents

Download

Before use, carefully read and observe the warning texts on the label.

1. Ensure surface is clean and dry.
2. Shake can vigorously for 2 minutes.
3. Invert the can and spray downwards 50-75mm from the surface. The closer the aerosol to the surface being marked, the narrower and more accurate the lines. Use masking tape when required to increase line accuracy and sharpness. The speed of movement controls the density of the marked line.
4. IMPORTANT! After use: turn can upright and face away from user. Spray for a few seconds to clear the nozzle.

Surface Preparation
Proper surface preparation is essential for the success of any protective coating system. Before you begin ensure the area is free from any dust, oil, grease, old coatings and surface contaminants.

The preparation of steelwork prior to painting generally falls into two main areas; that of degreasing and the removal of rust and scale.
All surfaces to be painted should be clean, dry and free from loose and flaking material, dust, grease and millscale, etc.
Prime bare surfaces with Palatine Anti-Corrosive Metal Primer or Palatine All Purpose Primer / Undercoat in accordance with our recommendations
For non-ferrous metals use Palatine Fast Dry etching primer.
Rub down previously gloss painted surfaces with fine waterproof abrasive paper and rinse thoroughly.

Mixing
Stir the paint with a drill stirrer or wooden baton at least 2” wide. Continue to stir during application.

Application
Best results are obtained in warm (minimum 10°C), dry conditions.

Mix thoroughly for approximately 2 minutes using a drill stirrer. A wooden batten at least 25mm wide is also ideal.
Apply an even coat using a brush, short to medium pile roller on smooth surfaces and a long pile roller on textured surfaces
For spray application by either airless or conventional spray a dilution ration of no more than 10% is recommended with Palatine White Spirit by volume applying thin coats allowing each one to dry before applying subsequent coats.
Once dried, a second coat can be applied at full strength. This will prolong the life and performance of the coating.

Thinning and Cleaning: Use Palatine White Spirit.

If using more than one batch of the same colour, intermix before use

Preceding Coat
Prime bare surfaces with Palatine Anti-Corrosive Metal Primer or Palatine All Purpose Primer / Undercoat in accordance with our recommendations
For non-ferrous metals use Palatine Mordant Solution.

Subsequent Coat
A second coat is recommended for maximum protection.

Reviews

There are no reviews yet.

Survey Line Marking Spray Paint 750ml