A tin of Sandtex 365 All Weather masonry paint grey

FREE SHIPPING AVAILABLE ON ORDERS OVER £75.00*

Sandtex 365 White Masonry Paint 5L

Sandtex 365 White Masonry Paint is a solvent based, premium quality, smooth masonry paint.

Can be applied in temperatures as low as -10 degrees
Based on high performance Pliolite resin
Resistant to showers after only 20 minutes
BBA approved 15 years proven durability
Solvent-based, Matt finish

£44.69 exc VAT | £53.63 inc VAT

40 in stock

Stay Social. Connect with us.

Product Description

Sandtex 365 White Masonry Paint, like Palatine Pliocem Pliolite Masonry Paint, is a solvent based, premium quality, smooth protective and decorative finish. For use on most exterior masonry surfaces and exterior grade building boards which will allow the white masonry paint the ability to dry in adverse weather conditions and temperatures as low as -10ºC.

Sandtex 365 masonry paint offers up to 20 Years of Protection and has been tested and proven to withstand ‘all weather’ conditions. This makes it ideal for structures exposed to harsh conditions in winter, where Sandtex High Cover would not be suitable.

We also provide Sandtex 365 Masonry Paint in a range of colours, including the ability to produce custom colours upon request. For more details on this service, please contact us by web chat, phone or email.

Sandtex 365 White Exterior Masonry Paint Application

Apply using a brush or roller, or with an airless sprayer. Surfaces should be dry and free of anything that will interfere with the adhesion of the paint. On previously painted surfaces, loose and flaking material should be removed using a stiff brush (not wire).

Stir well before use and ensure the previous coat is fully dry before applying a new coat. Apply at least two full coats, with some colours possibly needing a further coat to give complete obliteration.

Touch dry in 1-2 hours. Leave 16 hours before overcoating.

Estimated Coverage: up to 10sqm per litre

Container Size: 5 Litre

For full technical, safety and application details, please see the data sheets.

For water based alternatives take a look at Sandtex Trade X-treme X-posure Smooth Masonry Paint or Palatine Trutex Masonry Paint

Product Documents

Download

Surface Preparation
Proper surface preparation is essential for the success of any protective coating system. Before you begin ensure the area is free from any dust, oil, grease, old coatings and surface contaminants.

The preparation of steelwork prior to painting generally falls into two main areas; that of degreasing and the removal of rust and scale.
All surfaces to be painted should be clean, dry and free from loose and flaking material, dust, grease and millscale, etc.
Prime bare surfaces with Palatine Anti-Corrosive Metal Primer or Palatine All Purpose Primer / Undercoat in accordance with our recommendations
For non-ferrous metals use Palatine Fast Dry etching primer.
Rub down previously gloss painted surfaces with fine waterproof abrasive paper and rinse thoroughly.

Mixing
Stir the paint with a drill stirrer or wooden baton at least 2” wide. Continue to stir during application.

Application
Best results are obtained in warm (minimum 10°C), dry conditions.

Mix thoroughly for approximately 2 minutes using a drill stirrer. A wooden batten at least 25mm wide is also ideal.
Apply an even coat using a brush, short to medium pile roller on smooth surfaces and a long pile roller on textured surfaces
For spray application by either airless or conventional spray a dilution ration of no more than 10% is recommended with Palatine White Spirit by volume applying thin coats allowing each one to dry before applying subsequent coats.
Once dried, a second coat can be applied at full strength. This will prolong the life and performance of the coating.

Thinning and Cleaning: Use Palatine White Spirit.

If using more than one batch of the same colour, intermix before use

Preceding Coat
Prime bare surfaces with Palatine Anti-Corrosive Metal Primer or Palatine All Purpose Primer / Undercoat in accordance with our recommendations
For non-ferrous metals use Palatine Mordant Solution.

Subsequent Coat
A second coat is recommended for maximum protection.