FREE SHIPPING AVAILABLE ON ORDERS OVER £75.00*
Teamac High Performance Marine Gloss
A two pack water based gloss for use both above and below the water-line.
- For use on GRP, wood, ferro concrete and suitably primed metals
- Does not support fungus growth and is easily cleaned
- Apply by brush, roller or airless spray
- Designed for use over Two Pack High Performance Primer
£43.79 – £181.66
Stay Social. Connect with us.
Product Description
Teamac High Performance Marine Gloss is a two pack water based coating for use on boats and marine surfaces. It is designed to be used both above and below the water-line, extending the lifespan of boats.
The coating will not fade or yellow when exposed to high levels of ultra violet light, making it suitable for exterior use. It also will not support fungus growth and can be easily cleaned of surface contaminants.
Please note that this coating can not be used over conventional solvent based paints. If you have any technical questions, please contact our team by web chat, phone or email. Emails sent outside of our office hours are checked the following working day.
High Performance Marine Gloss is designed to be used to overcoat Two Pack High Performance Primer. For a single pack marine gloss, see Teamac Marine Gloss or Carbosil Marine Gloss.
Please note: The colours on the product listings are only given as a guide. This is due to the fact that every computer monitor has a different capability to display colours. In addition, everyone sees these colours differently.
Surface Preparation
All surfaces should be laitance free, clean, dry, sound and free from contaminants.
Mixing Instructions
The product is supplied in two containers: one larger than the other and labelled Base. The other smaller one labelled Activator. The contents of the pack marked Activator are added to the contents of the larger pack marked Base and thoroughly mixed together, preferably by slow speed electric mixer for 2 minutes or until thoroughly mixed. Failure to mix the material correctly will lead to uncured areas in the coating.
Application Conditions
Apply between 5°C to 30°C by brush or short nap mohair roller. This product can also be spray applied in approved conditions. When brush or roller applied at ambient temperatures – these products do not emit free Isocyanate at above levels recommended by C.O.S.H.H. Regulations. However, the protective measures shown on the product labels and safety data sheets must be followed. When used at elevated temperatures or atomised (sprayed) these products do emit small amounts of free Isocyanate and should only be sprayed in an atmosphere controlled working area, with suitable ventilation or flame proof extraction of air. Operatives must wear suitable protective clothing and separate air fed breathing apparatus. It is recommended that spraying of these products be avoided wherever possible to facilitate uncomplicated application and site conditions.
Pot Life – Once the parts are mixed together the material has to be used within 6 to 8 hours.
Preceding Coat
Metal surfaces should be suitably primed with Teamac HP Primer Undercoat.
Subsequent Coat
Teamac High Performance Marine Gloss
Estimated Coverage
8sqm per litre
Product Documents
Surface Preparation
Proper surface preparation is essential for the success of any protective coating system. Before you begin ensure the area is free from any dust, oil, grease, old coatings and surface contaminants.
The preparation of steelwork prior to painting generally falls into two main areas; that of degreasing and the removal of rust and scale.
All surfaces to be painted should be clean, dry and free from loose and flaking material, dust, grease and millscale, etc.
Prime bare surfaces with Palatine Anti-Corrosive Metal Primer or Palatine All Purpose Primer / Undercoat in accordance with our recommendations
For non-ferrous metals use Palatine Fast Dry etching primer.
Rub down previously gloss painted surfaces with fine waterproof abrasive paper and rinse thoroughly.
Mixing
Stir the paint with a drill stirrer or wooden baton at least 2” wide. Continue to stir during application.
Application
Best results are obtained in warm (minimum 10°C), dry conditions.
Mix thoroughly for approximately 2 minutes using a drill stirrer. A wooden batten at least 25mm wide is also ideal.
Apply an even coat using a brush, short to medium pile roller on smooth surfaces and a long pile roller on textured surfaces
For spray application by either airless or conventional spray a dilution ration of no more than 10% is recommended with Palatine White Spirit by volume applying thin coats allowing each one to dry before applying subsequent coats.
Once dried, a second coat can be applied at full strength. This will prolong the life and performance of the coating.
Thinning and Cleaning: Use Palatine White Spirit.
If using more than one batch of the same colour, intermix before use
Preceding Coat
Prime bare surfaces with Palatine Anti-Corrosive Metal Primer or Palatine All Purpose Primer / Undercoat in accordance with our recommendations
For non-ferrous metals use Palatine Mordant Solution.
Subsequent Coat
A second coat is recommended for maximum protection.
Be the first to review “Teamac High Performance Marine Gloss”
You may also like…
Marine Coatings
£17.03 – £101.99
Marine Satin Paint
£17.84
Marine Coatings
£14.84 – £90.30
Marine Satin Paint
£16.30 – £64.40
Reviews
There are no reviews yet.