Product Description
Palatine Exterior Extra Durable Wood Stain Satin is a satin finish equivalent to Exterior Extra Durable Wood Stain Gloss. It is a translucent wood stain designed for use on outdoor wooden surfaces. The stain provides a UV stable and hard wearing satin finish that offers long lasting protection on exterior timber.
Exterior Wood Stain Satin contains a blend of silicone and urethane resins, which combine to create a durable coating that is suitable for doors, soffits, fascia and most timber. This allows various exterior wooden surfaces to be finished with the same stain, providing a consistent appearance to an outdoor space.
The translucent finish of this wood stain allows the grain of the wood to remain visible once coated, providing a more natural look to the surface. This preserves the natural beauty of the wood, while providing the protection and choice in colour of a paint.
Palatine Exterior Wood Stain is available in 15 different colours, including various shades of brown and grey. In addition to the colours on this page, we can supply other colours, including blues, greens and purples. Please contact us if you would like to know more about the other colours we can provide in this product.
At Palatine Paints, we manufacture our wood stains, rather that buying them in from an external supplier. This means we have complete knowledge of our coatings and their properties, as they have been developed by us. If you have any technical questions about this or any of our other products regarding preparation, surface compatibility, coverage, or anything else, please contact us.
Our technical team are available at any time during our opening hours through web chat, phone and email. You can also visit our shop to look at the range of colours we can provide or collect your order.
Drying Times and Coverage
Palatine Exterior Extra Durable Wood Stain is touch dry in 3 hours and hard dry in 24 hours. Leave 6 to 12 hours before overcoating.
Estimated Coverage: 12.5m² per litre
For full details on application, please see the ‘How To Apply’ section or the Technical Data Sheet.
Surface Preparation
On previously painted surfaces, ensure it is sound and non-flaking. Abrade the surface
removing all previous coatings, preferably by mechanical abrasion to provide a “key” and
maximise adhesion of the subsequent coating. For surfaces that have been exposed to
weathering clean with a mould and mildew remover. If any signs of insect wood boring or rot
has occurred use, remove and replace severely affected areas with a high performance wood
filler and then treat with a woodworm killer treatment.
Mixing
Stir the paint with a drill stirrer or wooden baton at least 2” wide. Continue to stir during application to avoid settling of the product.
Application
Apply by brush, solvent resistant roller or spray. Use a paint brush for cutting in if applicable. Avoid applying the paint too thickly to avoid delaying drying times. If the substrate is porous, thin the first coat with 10% White Spirit. The second and subsequent coats can be applied as soon as the first / preceding coat is dry usually after 6-12 hours, and should be applied within 5 days. If more than 5 days elapse, the previous coat should be lightly abraded before the second coat is applied.
Preceding Coat
For best results on new or weathered bare timber, treat with a solvent based clear wood
preservative applied as per the manufacturers guidance.
Subsequent Coat
Recommended 2-3 coats
Application Methods
Brush, Roller, Airless or Conventional Spray
Airless Spray: Tip size range: .009 – .011. Gun filter: Red (Very Fine). Always spray atthe lowest possible pressure which will give a good spray pattern.
Application by brush can achieve up to 80 microns dft.
When applying by roller, use a solvent resistant sleeve.
Avoid excessive film thickness as this will cause the product to run onto other surfaces and potentially cause through-drying problems.
Preparation:
To ensure a durable and effective bilge paint application, it’s crucial to properly prepare the surface. Start by cleaning the substrate thoroughly to remove any dirt, grease, or oil. You can use a degreaser or mineral spirits for this step. Next, inspect the surface for any rust or old paint. If present, remove the rust using a wire brush, sandpaper, grinder or suitable rust remover / treatment. For old paint, use a paint stripper or sand it down until you reach the bare metal. Once the surface is clean and free of rust and old paint, sand it with fine-grit sandpaper to create a smooth and slightly roughened surface for better paint adhesion. Finally, wipe down the steel with a clean cloth to remove any dust or debris before applying our rust-inhibitive marine primer. After the primer has dried, you can proceed with applying our high build marine undercoat and then one but preferably two coats of the bilge paint.
Application:
Best results are obtained in warm (minimum 10°C), dry conditions.
Mix thoroughly for approximately 2 minutes using a drill stirrer. A wooden batten at least 25mm wide is also ideal.
Apply an even coat using a brush, short to medium pile roller on smooth surfaces.
For spray application by either airless or conventional spray a dilution ration of no more than 10% is recommended with Palatine White Spirit by volume.
A second coat can be applied at full strength. This will prolong the life and performance of the coating.
For application onto wooden surfaces, a minimum of two coats is recommended.
Drying Time @ 20ºC: Drying times will be extended at low temperatures.
Do not apply when ambient temperature falls below 5ºC or relative humidity exceeds 90%.
Surface dry @ 20ºC: 1 hours
Hard dry @ 20ºC: 4 hours
Overcoat@ 20ºC: After 8 hours (temperature dependent).
Theoretical Coverage: 12 – 14m² per litre.
(Coverage rate can be affected by such variables as type and condition of substrate, type of application equipment and individual method of application.)
Storage: Store in temperature range 5-40ºC
Thinners: White Spirit
If you have any questions or require any further assistance, please contact us on 01942 884122 or email [email protected]
Reviews
There are no reviews yet.