Which Should I Choose?
Not sure if EpoxyTread is right for your project? Our guide to epoxy floor paint walks you through the differences between single-pack and two-pack systems, helps you assess your needs, and shows you how to choose the best option for your floor
EpoxyTread is a single-pack epoxy floor paint engineered for garages, warehouses, factories, and shop floors. You apply it straight from the can—no mixing required. The paint delivers superior chemical and oil resistance, making it ideal for environments where spills, solvents, and industrial fluids pose a risk. Surface dry time is just 3 hours, and you can recoat after 24 hours. Coverage reaches 12–14 m²/litre, and we recommend two coats for optimal durability and protection.
If your floor is subject to heavy traffic or heavy chemical spillages you may want to consider a Two Pack option. Ideal to use on concrete floors in factories and warehouses. It is also a great paint for garage floors, warehouses and shop floors.
Why Choose EpoxyTread Over Carbotread?
EpoxyTread delivers superior chemical and oil resistance compared to Carbotread polyurethane floor paint. This means you can confidently specify EpoxyTread for environments where spills, solvents, and industrial fluids pose a risk. Furthermore, the epoxy formulation resists staining and degradation far better than polyurethane alternatives, making it the ideal choice for workshops, factories, and commercial kitchens.
When to choose Carbotread instead: If you need a general-purpose, hard-wearing finish for mature concrete, wood, or metal floors without heavy chemical exposure, Carbotread polyurethane floor paint offers excellent durability at a competitive price point.
Key Features
- Single-pack formula – Apply straight from the can; no mixing, no waste
- Fast drying – Surface dry in 3 hours; recoat after 24 hours
- Superior chemical resistance – Resists oils, solvents, and industrial fluids
- Excellent coverage – 12–14 m²/litre
Suitable Surfaces
Apply EpoxyTread to mature concrete, wood, and metal floors. The paint works best on:
- Garage floors
- Warehouse floors
- Factory floors
- Shop floors
- Industrial work areas
- Commercial kitchens
Achieve enhanced durability by applying two coats of Epoxytread Single Pack Epoxy Floor Paint over Palatine’s Pliocem Concrete Sealer
Take a look at chlorinated rubber paint if you’re looking for a paint for an outdoor area that may be subject to chemical or urine splashes and which you need to clean with a jet wash etc. Epoxytread 1 part epoxy garage floor paint and many of our other floor paints, are available in several colour options. If you require a specific colour matched to your company livery etc, please get in contact with us.
Preparation
General: Ensure all surfaces are clean, dry, and free from contaminants like dust, grease, or oil.
Bare Concrete:
* Must be at least 4 weeks old (mature) with a moisture content below 8%.
* Remove any surface laitance (dusty layer).
* Smooth Concrete: Treat with concrete etching fluid to ensure a good “key,” then wash and dry thoroughly.
* Contaminants: Use Palatine Multi Purpose Thinners to remove traces of grease or oil.
Previously Painted Surfaces:
* Sand down thoroughly to improve adhesion and remove loose material.
* Power Floated Floors: These often have poor adhesion; they must be blast-treated or chemically etched first.
* Compatibility Test: It is recommended to test the paint on a small area first.
Wooden Floors: Sand down to remove existing coatings/loose material. Seal knots with a clear knotting solution.
Metal Floors: Ensure the metal is clean and free from rust or loose material.
Application
Mixing: This is a single-pack formula (no hardener needed). Mix thoroughly for approximately 2 minutes using a wide-bladed stirrer (at least 25mm wide).
Method: Can be applied via brush or roller.
Conditions: Best results are achieved in warm (minimum 15°C) and dry conditions.
Coats: Two coats are recommended for optimal durability and chemical resistance.
Product Comparison: EpoxyTread vs. Carbotread
| Feature |
EpoxyTread (Single-Pack Epoxy) |
Carbotread (Polyurethane) |
| Chemical Resistance |
Superior – Resists oils, solvents, industrial fluids |
Good – General wear; limited chemical protection |
| Application |
Single-pack (no mixing) |
Single-pack (no mixing) |
| Surface Dry Time |
3 hours |
Comparable |
| Coverage |
12–14 m²/litre |
Standard coverage |
| Best For |
Warehouses, factories, shops with chemical exposure |
General-purpose floors without heavy chemical risk |
| Durability |
Enhanced over Pliocem Concrete Sealer |
Hard-wearing gloss finish |
Q: Can I apply EpoxyTread without mixing?
A: Yes. EpoxyTread is a single-pack formula—simply open the can and apply. No mixing means faster application, less waste, and fewer mistakes.
Q: How long does EpoxyTread take to dry?
A: Surface dry time is 3 hours, and you can recoat after 24 hours. The floor is walk-on ready after 24 hours, though full hardness develops over several days.
Q: Can I use EpoxyTread on residential garage floors?
A: Absolutely. EpoxyTread is ideal for garage floors, especially if you store chemicals, oils, or solvents. The superior chemical resistance protects against spills and staining.
Q: How many coats do I need?
A: We recommend two coats for optimal durability and protection. One coat provides basic coverage; two coats deliver maximum longevity and chemical resistance.
Q: What’s the best way to prepare my concrete floor?
A: Clean thoroughly, remove grease and oil, etch smooth concrete, and check moisture content (below 8%). Do not apply to newly laid concrete—wait at least 4 weeks. Proper prep ensures excellent adhesion and a long-lasting finish.
Q: Can I apply EpoxyTread over existing paint?
A: Yes. Lightly sand the existing paint to create a key, then apply EpoxyTread. This helps the new coat bond securely to the old surface.
Reviews
There are no reviews yet.