Professional Satin Tile Paint

A satin finish paint with increased adhesion strength designed for use in tiled areas, such as kitchens and bathrooms.

  • Apply direct to tiles
  • Also available in a gloss finish
  • Touch dry in 3 hours
  • RAL Classic, BS 4800 and BS 381C colours also available




Stay Social. Connect with us. 

Product Description

Palatine Professional Satin Tile Paint is a solvent based paint with increased adhesion strength compared to our professional satin paint. Due to this, the tile paint can be applied directly to tiled surfaces.

This paint is ideal for use in kitchens and bathrooms, where tiled walls are often a highlight of the room. Our satin tile paint can be used to recoat tired tiles, or update their look with a fresh colour. You can use tile paint to redesign a room without needing to replace the existing tiles.

In addition to the colours shown here, we also match to RAL Classic, BS 4800 and BS 361C colours. For more information on this service, including prices, please contact our team.

Our friendly team is available to contact by phone or web chat during our opening hours, or by email, where overnight messages are replied to the next working morning. As our satin tile paint is a paint we manufacture, we are able to answer any technical questions you may have. This includes topics such as surface and coating compatibility, preparation and application.

We also supply this paint in a gloss finish that provides an eye-catching high sheen to the surface. For kitchen and bathroom decorating, we also have a cupboard paint available in a gloss or satin finish and a range of colours.

Please note: The colours shown here are only a guide. This is due to the fact that every computer monitor has a different capability to display colours. In addition, everyone sees these colours differently.

Colours Available: 3 Standard, BS 381C, BS4800 and Ral Classic range.

Pack Sizes: 1 Litre, 2.5 Litre, 5 Litre.

Coverage / Drying Times:

Surface Dry: 3 hours

Hard Dry: 24 hours

Overcoat: after 16 hours
Keep coated areas dry for a minimum of 24 hours following application.
Please note, drying times will be extended at low temperatures. Do not apply when ambient temperature falls below 10ºC

Theoretical Coverage: 12 – 14m² per litre.

(Coverage rate can be affected by such variables as type and condition of substrate, type of application equipment and individual method of application.)

Product Documents

Surface Preparation
Proper surface preparation is essential for the success of any protective coating system. Before you begin ensure the area is free from any dust, oil, grease, old coatings and surface contaminants.

The preparation of steelwork prior to painting generally falls into two main areas; that of degreasing and the removal of rust and scale.
All surfaces to be painted should be clean, dry and free from loose and flaking material, dust, grease and millscale, etc.
Prime bare surfaces with Palatine Anti-Corrosive Metal Primer or Palatine All Purpose Primer / Undercoat in accordance with our recommendations
For non-ferrous metals use Palatine Fast Dry etching primer.
Rub down previously gloss painted surfaces with fine waterproof abrasive paper and rinse thoroughly.

Stir the paint with a drill stirrer or wooden baton at least 2” wide. Continue to stir during application.

Best results are obtained in warm (minimum 10°C), dry conditions.

Mix thoroughly for approximately 2 minutes using a drill stirrer. A wooden batten at least 25mm wide is also ideal.
Apply an even coat using a brush, short to medium pile roller on smooth surfaces and a long pile roller on textured surfaces
For spray application by either airless or conventional spray a dilution ration of no more than 10% is recommended with Palatine White Spirit by volume applying thin coats allowing each one to dry before applying subsequent coats.
Once dried, a second coat can be applied at full strength. This will prolong the life and performance of the coating.

Thinning and Cleaning: Use Palatine White Spirit.

If using more than one batch of the same colour, intermix before use

Preceding Coat
Prime bare surfaces with Palatine Anti-Corrosive Metal Primer or Palatine All Purpose Primer / Undercoat in accordance with our recommendations
For non-ferrous metals use Palatine Mordant Solution.

Subsequent Coat
A second coat is recommended for maximum protection.


There are no reviews yet.

Be the first to review “Professional Satin Tile Paint”

You may also like…


A tin of Palatine Professional Satin Tile Paint
Professional Satin Tile Paint
£13.08£56.27 Select options
This site uses cookies to offer you a better browsing experience. By browsing this website, you agree to our use of cookies.